Hasil Pencarian  ::  Simpan CSV :: Kembali

"Nanopartikel Ni(OH)2 digunakan secara luas sebagai material katoda pada superkapasitor asimetrik karena memiliki sifat elektrokimia yang baik dan mudah didapat. Nanopartikel Ni(OH)2 diproduksi dengan metode hidrotermal. fasa dari hasil sintesis Ni(OH)2 dikarakterisasi menggunakan XRD, tercipta pola difraksi dari fasa Ni(OH)2 tanpa terlihat impurity dari pola difraksi. Didapat ukuran partikel hasil sintesis-Ni(OH)2 sebesar 16.285 +- 4.215 nm dari karakterisasi TEM. Untuk menambah sifat konduktivitas panas, dicampurkan β-Ni(OH)2 dengan karbon mesopori, dan dideposisi pada permukaan glassy carbon electrode. Karakterisasi menggunakan SEM-EDX dan XPS, menghasilkan spektrum perbandingan atom Ni : O sebesar 1 : 2 yang memperkuat dugaan terbentuknya Ni(OH)2. Karakterisasi pendahuluan menggunakan cyclic voltammetry menjelaskan bahwa penambahan material karbon mesopori tidak mendominasi karakter dari Ni(OH)2. Lalu, didapat hasil kapasitas spesifik dalam fungsi discharging sebesar 280C/g, 120 C/g, 30 C/g, dan 10 C/g untuk arus spesifik sebesar 1 A/g, 2 A/g, 5 A/g,dan 10A/g berturut-turut. Serta didapatkan nilai energi spesifik sebesar 39.72; 36.67; 22.92; 15.28 Wh/kg, dan nilai daya spesifik sebesar 0.55; 1.1;2.75; 5.5 kW/kg untuk arus spesifik 1 ;2; 5; 10 A/g secara berturut-turut. Hasil kapasitas spesifik dari Ni(OH)2 masih bertahan 96.59% pada siklus ke 3000.

---

Ni(OH)2 nanoparticle is widely used as cathode material in asymmetric supercapacitors due to its good electrochemical properties and affordable prices. Ni(OH)2 nanoparticles are synthesized via hydrothermal method. The phase from the as synthesized Ni(OH)2 was characterized using XRD, creating a diffraction pattern from the phase of Ni(OH)2 without any visible impurity from the diffraction pattern. The obtained particle size of Ni(OH)2 was 16.285+- 4.215 nm were measured by TEM characterization. To increase heat conductivity property, Ni(OH)2 was mixed with mesoporous carbon, and deposited on the surface of the glassy carbon electrode. Characterization using SEM-EDX and XPS, resulting in a comparison of determining the ratio of Ni : O at 1 : 2 which strengthens the suspicion of the formation of Ni(OH)2. Preliminary characterization using cyclic voltammetry explains mesoporous carbon material does not dispel characters from Ni(OH)2. the results of specific capacity are 280 C/g, 120 C/g, 30 C/g, and 10 C/g for specific currents of 1 A/g, 2 A/g, 5 A/g, and 10A/g consecutively. Specific energy values obtained were 39.72;36.67; 22,92;15.28 Wh/kg, and specific power values of 0.55; 1.1;2.75;5.5 kW/kg for specific currents 1;2;5;10 A/g respectively. The results of the specific capacity of Ni (OH) 2 still survive at 96.59% in the 3000 cycle."

"[ABSTRAKHidrogen merupakan salah satu unsur yang dapat dijadikan sebagai bahan bakar alternatif karena BBH atau bahan bakar hidrogen bersifat ecoenergi dengan proses pembakaran yang hanya menghasilkan air dan energi (listrik dan panas). Salah satu teknologi penghasil hidrogen adalah dengan metode Contact Glow Discharge Elektrolisis atau CGDE. Penelitian ini menggunakan metode CGDE dengan multi katoda dan penambahan etanol dengan tujuan dapat meningkatkan laju produksi hidrogen dan efektivitas proses.pada penelitian ini akan dilihat pengaruh penambahan jumlah katoda, pengaruh konsentrasi etanol dan diameter katoda terhadap laju produksi dan efektivitas hidrogen. Dari karakterisasi arus dan tegangan yang diperoleh pada penelitian ini, dapat disimpulkan bahwa arus akan semakin meningkat seiring dengan bertambahnya jumlah katoda. Penggunaan multi katoda pada proses CGDE juga terbukti meningkatkan produksi hidrogen pada tegangan dan konsumsi energi yang sama. Penambahan zat aditif etanol juga dilakukan pada penelitian ini dan memperoleh hasil bahwa semakin tinggi konsentrasi etanol maka akan semakin tinggi produksi dan efektivitas gas Hidrogen yang dihasilkan. Selain itu, penelitian ini juga membuktikan bahwa semakin besar diameter katoda maka laju produksi akan semakin tinggi, namun konsumsi energi menjadi meningkat dan tidak sebanding dengan peningkatan laju produksi sehingga menghasilkan efektivitas yang semakin kecil. Proses CGDE multi katoda pada penelitian ini menunjukkan peningkatan efektivitas proses sebesar 76 kali lipat dibandingkan dengan elektrolisis Faraday.

---

ABSTRACTHydrogen is one of elements that can be used as an alternative energy. The combustion of Hydrogen only produces water and energy. Therefore, hydrogen is called as ecoenergy. One of technology that can produce hydrogen is Contact Glow Discharge Electrolysis or CGDE. CGDE is one of plasma electrolysis that uses electrolyte solution and inert electrode to produce hydrogen in high voltage. This research uses CGDE method with multi-cathode and ethanol in order to increase hydrogen production and the effectivity of process. In this research, we will explore the effect of increasing cathode number, etanol addition, and increasing of cathode diameter. From characterization of current and volatge, we can conclude that the increasing of cathode number can increase the current that through into cathode. Utilization of multi-cathode in CGDE is proven that can increase the hydrogen production at the same voltage and energy consumption. The addition of ethanol has done in this research and we can conclude that when we increase the concentration of ethanol, the hydrogen production will be increased either at the same voltage. In addition, this research also prove that the bigger diameter of a cathode will increase the production rate, but the energy consumption increases higher than the production rate. Therefore, the increasing of diameter of cathode is not effective to use in CGDE. The CGDE multi-cathode on this research indicated increasing of effectiveness as much as 76 times higher than the Faraday Electrolysis., Hydrogen is one of elements that can be used as an alternative energy. The combustion of Hydrogen only produces water and energy. Therefore, hydrogen is called as ecoenergy. One of technology that can produce hydrogen is Contact Glow Discharge Electrolysis or CGDE. CGDE is one of plasma electrolysis that uses electrolyte solution and inert electrode to produce hydrogen in high voltage. This research uses CGDE method with multi-cathode and ethanol in order to increase hydrogen production and the effectivity of process. In this research, we will explore the effect of increasing cathode number, etanol addition, and increasing of cathode diameter. From characterization of current and volatge, we can conclude that the increasing of cathode number can increase the current that through into cathode. Utilization of multi-cathode in CGDE is proven that can increase the hydrogen production at the same voltage and energy consumption. The addition of ethanol has done in this research and we can conclude that when we increase the concentration of ethanol, the hydrogen production will be increased either at the same voltage. In addition, this research also prove that the bigger diameter of a cathode will increase the production rate, but the energy consumption increases higher than the production rate. Therefore, the increasing of diameter of cathode is not effective to use in CGDE. The CGDE multi-cathode on this research indicated increasing of effectiveness as much as 76 times higher than the Faraday Electrolysis.]"

"Telah dilakukan sintesis LiFePO4/C sebagai material katoda baterai lithium ion dengan menggunakan metode hidrotermal dari bahan LiOH, NH4H2PO4, FeSO4.7H2O, carbon black dan sukrosa. Proses hidrotermal dilakukan pada suhu reaktor 180⁰C dengan lama waktu penahanan 20 jam. Penambahan karbon dilakukan dengan 2 cara. Pertama menggunakan sukrosa sebagai sumber karbon yang dilarutkan bersama prekusor dan kedua menggunakan carbon black yang ditambahkan setelah proses hidrotermal sebelum proses kalsinasi. Temperatur kalsinasi divariasikan pada 500, 600 dan 750⁰C selama 5 jam. Proses dekomposisi termal dianalisis menggunakan DTA-TGA analyzer, karakterisasi fasa dilakukan dengan XRD, morfologi dengan SEM/EDX, nilai konduktifitas dan kapasitansi material dengan LCR-EIS, dan performa baterai dengan pengujian charge-discharge menggunakan baterai analyzer. Hasil LiFePO4/C yang murni berbentuk flake berhasil disintesis dengan penambahan carbon black 5 wt%, sedangkan untuk penambahan karbon melalui pelarutan sukrosa masih terdapat pengotor Fe3(PO4)2 pada hasil kalsinasi. Temperatur kalsinasi optimal adalah 750⁰C dengan ukuran kristalit 39,7 nm, tebal butiran flake 80 nm dan besar butiran rata-rata 427 nm. Konduktifitas LiFePO4 murni terukur 5 x 10-7 S/cm dan konduktifitas LiFePO4/C adalah 2,23 x 10-4 S/cm yang dihasilkan dari sampel dengan tambahan carbon black 5wt% kalsinasi 750⁰C. Dari pengujian charge/discharge didapatkan siklus terbaik dihasilkan oleh sampel LiFePO4/C yang dikalsinasi 750⁰C yang stabil dengan tegangan 3,3-3,4 V, kapasitas spesifik dihasilkan pada 0,1 C = 11,6 mAh/g ; 0,3C = 10,78 mAh./g dan 0,5 C = 9,45 mAh/g.

---

LiFePO4/C has been succesfully synthesized through hydrothermal method from LiOH, NH4H2PO4, and FeSO4.7H2O as starting materials and either carbon black or sucrose as carbon source used as cathode material for lithium ion batteries. In this work, hydrothermal reaction temperature was at 180C for 20 hours.Carbon sources were added in two routes. Firstly, sucrose solution was mixed with precursor solution before hydrothermal reaction. Secondly carbon black was added after hydrothermal reaction before calcination process. Calcination temperatures were performed at 500, 600, and 750C each for 5 hours. Thermal decomposition process was analyzed using DTA-TGA analyzer, phases and morphological were characterized by using XRD and SEM/EDX measurement, conductivity and electrical capacity were characterized by EIS measurement, and batteries performance were tested with charge discharge testing by battery analyzer. Pure LiFePO4/C flake shaped was successfully synthesized with the addition of 5 wt% carbon black, while the addition of carbon through the dissolution of sucrose still contained impurity from Fe3(PO4)2 in calcination product. Optimal calcination temperature was obtained at 750⁰C with crytallite size of 39.7 nm, flake particles diameter of 80 nm with particles average length of 427 nm. Pure LiFePO4 conductivity was measured to be 5 x 10-7 S/cm and conductivity LiFePO4/C was 2.23 x 10-4 S/cm produced from samples with carbon black addition of 5 wt% and calcined at 750⁰C. Charge/discharge cycles test showed that best battery performance was obtained from the sample with carbon black of 5wt% calcined at 750⁰C, with a stable voltage 3.3 to 3.4 V, specific capacity of 0.1 C = 11.6 mAh/g ; 0.3C = 10.78 mAh./g dan 0.5 C = 9.45 mAh/g."

" ABSTRAK Telah dilakukan proses sintesis LiFe 1-x VxPO4/C untuk katoda baterai litium ion. Pada bahan ini, sintesis diawali dengan pembuatan LiFePO4 yang dilakukan melalui proses hidrotermal dengan bahan dasar LiOH, NH4H2PO4 dan FeSO4.7H2O. Setelah LiFePO4 disintesis, lalu dilakukan penambahan variasi vanadium serbuk yang bersumber dari H4NO3V dan karbon yang berasal dari hasil pirolisis sukrosa selama 2 jam pada 400 C. Bahan-bahan dicampur menggunakan ball-mill lalu dikarakterisasi menggunakan analisis termal STA untuk menentukan temperatur sintering. Hasilnya memperlihatkan bahwa transisi terjadi pada temperatur sekitar 700 C yang kemudian dijadikan patokan untuk menentukan proses sintering. Sintering dilakukan selama 4 jam lalu hasilnya dikarakterisasi menggunakan difraksi sinar-X XRD . Struktur mikto dan morfologi permukaan selanjutnya dianalisis menggunakan mikroskop elektron SEM . Hasil karakterisasi dengan XRD menunjukkan bahwa fasa LiFe 1-x VxPO4/C telah terbentuk dengan struktur berbasis olivin. Hasil SEM menunjukan adanya persebaran partikel LiFe 1-x VxPO4/C walaupun beberapa terlihat masih beraglomerasi. Proses pembuatan baterai dilakukan dari bahan hasil sintesis dan diuji menggunakan electrochemical impedance spectroscopy EIS dan uji performa melalui cyclic voltametry CV dan charge and discharge CD . Hasil EIS menunjukan bahwa doping dengan vanadium meningkatkan konduktifitas yang cukup berarti. Hal yang sama juga terjadi dengan adanya karbon sintesis dari sukrosa walaupun masih lebih rendah jika dibandingkan dengan karbon komersial. Uji performa menunjukan bahwa penambahan vanadium meningkatkan kapasitas 51.06 mAh/g saat charging dan 49.42 mAh/g saat discharging dengan beda potensial 3.581 V saat charging dan 3.319 V saat discharging. Hasil yang didapatkan ini cukup menjanjikan untuk penggunaan selanjutnya sebagai katoda baterai litium ion.

---

ABSTRACT Synthesis of LiFe 1 x VxPO4 C used for lithium ion battery cathode has been carried out. In the process, the synthesis was begun by synthesizing of LiFePO4 through a hydrothermal method with the precursors of LiOH, NH4H2PO4 and FeSO4.7H2O. The as synthesized LiFePO4 was then mixed with H4NO3V and carbon pyrolyzed from sucrose for 2 hours at 400 C. The mixture was mixed in a ball mill and then was characterized using a thermal analyzer to determine the transition temperature at which sintering at 700 C for 4 hours was obtained. X ray diffraction XRD was performed to analyzed the crystal structure whereas scanning electron microscope SEM was used to examine the microstructure and surface morphology. XRD results show that the phase LiFe 1 x VxPO4 C has been formed with an olivine based structure. SEM results showed the distribution of LiFe 1 x VxPO4 C particles are mostly distributed. The batteries were prepared from the as synthesized materials and was tested using electrochemical impedance spectroscopy EIS , cyclic voltammetry CV and charge and discharge CD performance test. The EIS results showed that doping with vanadium improved the conductivity. The same was true with the carbon even at a smaller value compared to that of the commercial one. The performance test showed that the addition of vanadium increased the capacity of about 51.06 mAh g with a potential of 3.581 V at charging and 49.42 mAh g with a potential of 3.319 V at discharging. These results are promising in terms of using this material for lithium ion battery cathode development."