Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 5 dokumen yang sesuai dengan query
cover
Yendri Minggu Bali
"Pengembangan perangkat mikro yang baru dan inovatif sangat tergantung pada sistem dan proses manufaktur yang dapat diandalkan untuk memproduksi komponen berskala mikro dengan kualitas yang baik. Salah satu jenis manufaktur ini adalah fabrikasi mikro dengan menggunakan mesin Laser CO2.
Penelitian ini dilakukan berupa eksperimen proses fabrikasi micropattern dengan beberapa variasi variabel bebas seperti jarak fokus, daya Laser dan kecepepatan nozzle Laser dengan metoda engraving menggunakan mesin Laser CO2 pada material acrylic dengan tebal 4 mm.
Hasil fabrikasi diamati dan diukur menggunakan microscope digital dan surface tester SURFCOM untuk memperoleh variabel tak bebas fabrikasi berupa nilai kekasaran permukaan, lebar, dan kedalaman. Hubungan antara kedua variabel ini dianalisis dengan response surface methodology (RSM) yang menghasilkan persamaan hubungan untuk kedua variabel. Hasil analisis RSM menunjukkan bahwa variabel daya (P) memberikan hubungan yang linear terhadap kekasaran permukaan (Ra) dengan variabel kecepatan kecepepatan nozzle Laser sebagai variabel yang memberi pengaruh untuk kualitas permukaan yang baik (halus). Pada dimensi geometri pengaruh daya Laser (P) memberikan hubungan linear dengan pengaruh yang signifikan.
Hasil analisis RSM memberikan grafik karakteristik dan juga persamaan matematik untuk kedua variabel yang dimanfaatkan untuk memprediksi kualitas hasil fabrikasi untuk membuat produk micromold. Hasil fabrikasi pola mikro untuk micromold ini diperoleh dengan kualitas nilai kekasaran permukaan (Rax) 17,55 µm, lebar celah (W) 135 µm dan kedalaman (D) 341 µm.

The development of innovative micro components depends on the manufacturing system and process that reliable to produce the component in micro scale with good quality. In this case, using CO2 Laser is one of micro fabrication technique to fabricate material to get micro component.
In this research, do an experiment to fabricate micropattern using engraving methode by Laser CO2 machine with several independent variables such as focus distance of nozzle Laser to workpiece (F), power of Laser (P), and velocity of nozzle Laser movement (V). The workpiece in this research is an acrylic.
Result of fabrication process will be identified and measured using digital microscope and surface roughness tester to get the value of workpiece quality such as surface roughness and geometrical properties as the dependent variables. The relationship of both variables will be expressed in 3D curves characterictic and mathematical models were analyzed by response surface methodology (RSM).
The result of the analysis indicate that power of Laser (P) and velocity of Laser nozzle movement (V) effect is the significant variables affecting the quality of micropattern and micromold fabrication. Micromold can be fabricated using Laser CO2 with roughness value (Rax) is 17,55µm, width of grove (W) 135 µm, depth (D) 341 µm.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S55703
UI - Skripsi Membership  Universitas Indonesia Library
cover
Hendrik Kurniawan
"ABSTRAK
Dengan mengfokuskan berkas pulsa laser karbon dioksida pada berbagai macam target pada tekanan rendah, akan terbentuk plasma yang unik. Dalam disertasi ini struktur dan dinamika dari plasma yang unik ini dapat diperoleh dengan mengembangkan metode pengamatan plasma yang baru yaitu pengukuran distribusi ruang dari intensitas emisi pada berbagai waktu tunda. Plasma ini terdiri atas daft bagian; pertama yaitu bagian kecil dari plasma (disebut plasma primer) yang memancarkan spektrum emisi kontinu hanya untuk beberapa seat diatas permukaan target. Bagian yang lain (plasma sekunder) mengembang sesuai waktu disekeliling plasma primer, memancarkan spektrum garis atomik yang sangat tajam dengan emisi latar belakang yang sangat rendah.
Juga ditunjukan bahwa emisi dari atom-atom yang terpancar keluar dari target membentuk struktur kulit (tipis), dan ionisasi dari atom-atom berlangsung lebih lambat dari pada eksitasi dari atom-atom netral. Laju pergeseran dari muka emisi adalah sebanding dengan waktu pangkat due per lima. Juga berhasil diamati bahwa titik dimana sinyal emisi mulal tampak adalah sama untuk berbagai macam target meskipun berbeda pada berat atomnya. Hasil ini mendukung model bahwa plasma sekunder dibentuk mengikuti prinsip gelombang kejut dengan plasma primer sebagai sumber energi awal.
Dengan memakal gas helium dan argon disekeliling target pada tekanan rendah, dua proses eksitasi yang berbeda terjadi pada saat pembentukan plasma sekunder. Proses eksitasi pertama disebabkan oleh mekanisma gelombang kejut, sedangkan eksitasi kedua disebabkan oleh tingkat energi metastabil pada gas mulia. Proses eksitasi kedua ini menyalurkan energi metastabil yang disimpan oleh gas mulia pada atom-atom yang dipancarkan oleh target meskipun lama setelah pulsa laser berakhir, sehingga menghasilkan intensitas emisi yang lebih tinggi di gas mulia dibandingkan di udara.
Temperatur tinggi pada plasma sekunder sebagai akibat dari kecepatan propagasi yang tinggi dari muka plasma menyebabkan plasma ini sangat cocok digunakan untuk mendeteksi atom-atom halogen yang biasanya sangat sukar diidentifikasi karena tingkat energinya yang sangat tinggi. Aplikasi analitis untuk mendeteksi unsur halogen pada contoh bubuk kimia maupun kalsium pada bahan makanan menunjukkan hubungan yang linter pada kurva kalibrasi. dalam metode Laser Microprobe Spectrochemical Analysis (LHSA) yang umum dipakai hingga saat ini untuk analisa spektrokimia, tidak terdapat hubungan yang tinier pada kurva kalibrasinya karena timbul penyarapan sendiri (self absorption) yang sangat kuat, .lumlah minimum yang dapat dideteksi untuk Cl adalah 5 ppm dan 10 ppm untuk Ca, yang mane Jauh lebih balk dibandingkan dengan metode Induction Couple Plasma (ICP) maupun metode lain. Hingga saat ini metode ICP adalah metode ter-balk yang banyak dipakal untuk analisa elemen-elemen pads bahan makanan. Metode kami akan dikembangkan menjadi metode analisa kuantitatif yang cepat, akurat dan. memiliki sensitivitas yang tinggi tidak Baja pada bahan makanan tetapi juga pada bahan biologi, geologi dan lain-lain.

ABSTRACT
A study has been conducted on the formation of the unique plasma generated by focusing a TEA CO2 laser onto various targets with low pressure surrounding gases. A new method of time-resolved measurement of spatial distribution of the plasma was carried out for analyzing the plasma structure and dynamics. The unique laser induced plasma consists of two distinct regions; the first is a small area of plasma (called primary plasma), which gives off intense continuous emission spectra for a short time just above the surface of the target. The other area (secondary plasma) expands with time around the primary plasma, emitting sharp atomic line spectra with negligibly low background signals.
It is clearly shown that emission due to the gushed atoms from the target form shell structure, and the ionization of the atoms proceeds at slower rate than the excitation of the neutral atoms. The displacement of the emission expansion is proportional to the two-fifths power of time. It has been also observed that the rising point in the time-resolved spatial distribution of the emission 1s the same regardless of the difference in atomic weight. These results support the model that the secondary plasma is excited by a shock wave with primary plasma serving as the initial explosion source.
By using helium and argon as a surrounding gases, two different excitation processes take place in farming the secondary plasma. The first excitation process is due to the shock wave mechanism, while the second process is due to the metastable state of the noble gases. It is believed that this second process transfers metastable energy to the vaporized atoms of the target for emission, even long after the laser bombardment ends, thus giving total emission intensity that is higher in the noble gases than yielding in air.
The high temperature generated in the secondary plasma as a result of its high propagating front speed has made it favorable for use in detecting atoms such as halogens which are usually very difficult to identify because of their high lying electronic energy level. Analytical application to the detection of halogen atoms in chemical powder and calcium in food material shows good linearity in the calibration curve. In the ordinary Laser Microprobe Spectra-chemical Analysis (LMSA), the calibration curve is not linear due to the strong self absorption. The detection limit of Cl, Ca is 5 ppm and 10 ppm respectively which is-better than ICP (50 ppm for Cl) and other methods. So far, ICP emission spectrometry has been used as the most convenient method for simultaneous multi elemental analysis of food materials. Our method will be developed as a rapid, high-precision, highly sensitive quantitative analytical method for not only food materials but also other biological and geological samples.
"
Depok: Universitas Indonesia, 1992
D177
UI - Disertasi Membership  Universitas Indonesia Library
cover
Rinda
"A TEA CO2 laser pulse (50 mJ, 100 ns) was focused under reduced pressure on the silicone grease painted on copper plate as a sub-target with a power density of 6 GW/cm2. The comparison was made on the characteristics of the induced laser plasma between the two cases, with sub-target and without sub-target. It is proved that emission spectrum assigned to silicone atom can be detected only for the case with sub-target. It is also proved that in the absence of the sub-target, the gushing speed of the atoms is very low, while for the case with sub-target, the gushing speed of atoms becomes very fast. It is shown that the setting of sub-target is very effective to make laser-induced shock-wave plasma and it is very effective to realize quantitative analysis of soft material."
Depok: Program Pascasarjana Universitas Indonesia, 1998
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Badruzzaman
"Mikrofluidik merupakan ilmu yang mengacu pada bidang sains dan teknologi dengan salah satu bidangnya adalah biomedical untuk memanipulasi fluida dalam suatu jaringan di dalam channel yang dimensinya antara 5 - 500 µm. Tahapan proses yang dilakukan pada teknologi microfabrication yaitu desain, microstucturing dan back-end processes. Passive mixing adalah proses pencampuran fluida dimana fluida yang bergerak dan part pencampur diam tanpa ada pergerakan dan tekanan dari luar atau proses pencampurannya terjadi karena bentuk desain channel yang khusus untuk pencampuran tersebut. Desain passive mixing adalah suatu bentuk dari channel yang di inginkan. Microstucturing adalah metode teknologi yang digunakan untuk pembentukan mikrofluidik, sedangkan back-end processes merupakan proses untuk joining material yang telah dilakukan pembentukan channel.
Dalam penelitian ini, proses desain channel menggunakan software autodesk inventor. Untuk proses microstucturing menggunakan laser CO2 daya rendah. Penggunaan laser CO2 sebagai alat pemotong untuk pembentukan mikrofluidik pada material acrylic menggunakan parameter yang dapat mempengaruhi hasil pemotongan, yaitu daya laser, kecepatan pemotongan dan ukuran jarak desain, kemudian dilakukan pengamatan terhadap hasil pemotongan tersebut yaitu ukuran hasil pemotongan dengan microscope digital microchannels serta dengan alat uji surface roughness. Tahapan terakhir dari microfabrication adalah back-end processes, proses joining dengan menggunakan metode thermal bonding untuk membuat mikrofluidik yang dibentuk dapat berfungsi dengan baik. Dari hasil penelitian pembentukan perangkat mikrofluidik dan percobaan pengaliran cairan pada channel yang merupakan bagian dari perangkat mikrofluidik telah berhasil dilakukan.

Microfluidics is a science which refers to the field of science and technology is one of the biomedical fields to manipulate fluids in a channel network in the dimensions between 5-500 µm. Stages of the process are carried out in microfabrication technology which are designs, microstucturing and back-end processes. Passive mixing is the process of mixing of the fluid in which the fluid is moving and stationary parts mixer without any movement and pressure from the outside or the mixing process occurs due to the special form of channel design for the mixing. Design is a form of passive mixing of the desired channel. Microstucturing technology is a method used to mikrofluidics formation, while the back-end processes is the process for joining materials that have done channel formation.
In this study, the process of channel design used Autodesk Inventor software. For microstucturing process used low-power CO2 laser. CO2 laser was used as a cutting tool for microfluidic fabrication on acrylic material the parameters that can affect the outcome are the cutting, the laser power, cutting speed and distance measures design. Then observations on the results of the cuts was perfomed by measuring the results of cutting the microchannels with digital microscope and surface roughness equipment. Final stage of the microfabrication was the back-end processes which are joining processes using thermal bonding method for making microfluidics to be function properly. The establishment of research and experiments on microfluidic flow of fluid in the channel which is part of the microfluidic has been successfully carried out.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T35405
UI - Tesis Membership  Universitas Indonesia Library
cover
Nevada Permata Anvini
"Latar belakang: Silver Diamine Fluoride dan Laser CO2 merupakan alternatif perawatan yang dapat dipilih untuk menangani hipersensivitas denton.
Tujuan: Mengetahui efektivitas penggunaan Silver Diamine Fluoride dan Laser CO2 dalam menurunkan skor hipersensitivitas dentin.
Metode: Penelitian ini menggunakan desain single blind, split-mouth randomized controlled trial yang melibatkan 16 subjek dengan keluhan gigi sensitif dan memiliki minimal dua gigi yang positif terhadap uji evaporatif atau uji thermal. Subjek akan diaplikasikan Silver Diamine Fluoride dan Laser CO2. Pengukuran hipersensitivitas dentin dilakukan dengan stimulus evaporatif dan termal dan DIAGNOdent pasca aplikasi, 7 hari dan 14 hari setelah aplikasi.
Hasil: Terjadi penurunan skor Hipersensitivitas dan DIAGNOdent yang berbeda bermakna terhadap data baseline segera pasca aplikasi, 7 hari dan 14 hari pasca aplikasi p=0,000 untuk stimulus evaporatif, termal dan DIAGNOdent . Tetapi tidak terdapat perbedaan bermakna secara statistik antara aplikasi Silver Diamine Fluoride dan aplikasi Silver Diamine Fluoride dan Laser CO2 pada setiap pengukuran.
Kesimpulan: Penggunaan Silver Diamine Fluoride dan Laser CO2 efektif dalam menurunkan skor hipersensitivitas dentin.

Background: Silver Diamine fluoride and CO2 Laser are a new alternative treatment for dentin hypersensitivity.
Objective: To evaluate the efficacy of Silver Diamine Fluoride and CO2 Laser in reducing dentin hypersensitivity score.
Methods: The study used a single blind, split mouth design randomized controlled trial involving 16 subjects with symptoms of sensitive teeth and have at least two hypersensitive teeth which are positive to evaporative or thermal test. The subject teeth surface will be applied Silver diamine fluoride and CO2 Laser will be applied to the subject teeth surface.
Results: This clinical study demonstrated that the application of Silver Diamine Fluoride and CO2 Laser reduce dentin hypersensitivity significantly in each measurement p 0,000 for evaporative and thermal stimulus. But there is no statistically significant differences between the two application.
Conclusion: The usage of Silver Diamine Fluoride and CO2 Laser are effective to reduce the degree of dentin hypersensitivity.
"
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2016
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library