Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 166880 dokumen yang sesuai dengan query
cover
Anhar Raiardi
"Biocomposite fiberboards using thermoplastic adhesive polymer white glue polyvinyl acetate and two types of natural fibers, rice straw and coir fibers, were made by vacuum bag moulding. The influences of fiber loading on the biocomposite?s tensile and behavior to water properties were investigated. Prior to the fabrication of the biocomposite the natural fibers were treated using the the alkali process by soaking the fibers in NaOH 5%. Three kind of fiber board were fabricated, a biocomposite with a variation of rice straw fiber loading, a biocomposite with a mixture of 50% rice straw and 50% coir whose fiber loading was also varied, and last a biocompsite with a 30% fiber loading mixture with a variation of coir fiber loading. The biocomposites fabricated had a gradual increase of tensile strength to an optimum fiber loading which after drops with the increase of fiber loading. Rice straw based composites had an optimum fiber loading of 30% percent and the the composite with a mixture of 50% rice straw and 50% coir dah an optimum fiber loading of 35%. The increase of fiber loading also increase the water content and the water absorption for all biocomposites fabricated. The study showed that rice straw and coir fibers may not work well with PVAc as reinforcing filler but showed similar trends when varying the fiber loading with other using natural fibers."
Depok: Universitas Indonesia, 2013
S54018
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tri Lika Jayanti Budi Ranti
"Jerami padi dan ampas tebu merupakan limbah alam yang berpotensi untuk dijadikan papan serat. Polivinil asetat sebagai perekat dipilih karena termasuk polimer yang tidak terlalu mahal sehingga memungkinkan untuk membuat papan hibrida serat jerami padi - ampas tebu yang murah dan juga ramah lingkungan. Perlakuan kimia diterapkan pada kedua serat untuk memperbaiki mutu serat jerami padi dan ampas tebu sebelum dijadikan penguat pada papan hibrida.
Penelitian ini bertujuan mengetahui komposisi terbaik papan jerami berbasis lem putih PVAc dan pengaruh penambahan ampas tebu dalam papan jerami padi, untuk mendapatkan komposisi terbaik juga mendapatkan sifat fisis dan mekanik terbaik. Komposisi optimal papan serat jerami padi sebesar 30 wt% menghasilkan kekuatan tarik sebesar 4.8 MPa sedangkan komposisi optimal papan hibrid jerami padi-ampas tebu adalah komposisi 15 wt% jerami padi, 15 wt% ampas tebu dan 70 wt% PVAc menghasilkan kekuatan tarik sebesar 3.7 MPa. Rata- rata kerapatan yang didapatkan pada papan hibrida adalah 0.75 gr/cm3 dengan kadar air 10% dan daya serap air mendekati 100%. Sifat mekanik dan sifat fisis papan hibrida yang tidak terlalu baik dikarenakan perekat yang digunakan mempunyai kuat tarik lemah, viskositas tinggi dan larut dalam air.

Rice straw and bagasse are natural waste materials that have the potential to be used as fiber boards. Polyvinyl acetate adhesives have been employed because it is relatively economical and this is possible to produce relatively cheap and eco-friendly rice straw-bagasse hybrid boards. Chemical treatment applied to improve the quality of rice straw and bagasse prior the rice straw ? bagasse hybrid board production.
This study aimed to determine the optimum composition of rice straw - PVAC white glue boards and the effects of bagasse addition to rice straw boards in order to achieve the optimum composition that provides the best physical and mechanical properties. Optimal composition of rice straw boards was in 30 wt% rice straw that provide a tensile strength of 4.8 MPa, while the optimal composition of hybrid boards is 15 wt% rice straw, 15 wt% bagasse and 70 wt% PVAc resulted a tensile strength of 3.7 MPa. Average density obtained on the hybrid fiber board was 0.75 gr/cm3 with 10 % moisture content and close to 100 % of water absorption. The mechanical and physical properties of these hybrid boards were not very good due to the adhesive used that had a low tensile strength, high viscosity and high water solubility."
Depok: Universitas Indonesia, 2013
S53179
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sirait, Rendy Audy
"Limbah pertanian di negara agraris seperti Indonesia sangatlah potensial. Pengolahan limbah pertanian seperti jerami padi akan memberikan nilai tambah ekonomis bagi para petani di Indonesia. Salah satu caranya adalah dengan pembuatan biokomposit perupa papan serat jerami dan serat gelas dengan polimer PVAc. Papan serat ini berpotensi menjadi material struktur yang murah dan mudah di dapat dikarenakan jumlahnya yang melimpah dan murah. Untuk meningkatkan kekuatan jerami dalam pembuatan papan serat dilakukan proses awal berupa perendaman jerami dalam cairan NaOH. Hal ini dilakukan untuk memperbaiki sifat mekanis jerami. Untuk mendapatkan komposisi yang terbaik maka dibuat beberapa komposisi serat papan jerami mulai dari 20% berat serat hingga 70% berat serat.
Komposisi optimal papan serat jerami padi berada pada 30% berat serat dengan kekuatan tarik sebesar 4.5 MPa. Variasi subtitusi serat gelas pada komposisi optimal papan jerami padi menghasilkan kekuatan optimal pada komposisi 50% jerami padi, 50% serat gelas dan 70% PVAc yaitu sebesar 4.26 MPa. Rata- rata kadar air 10% atau dibawah 13% menunjukkan papan serat ini sesuai dengan SNI 01-4449-2006.

Agricultural waste in an agricultural country like Indonesia is very potential . Processing of agricultural wastes such as rice straw provides economic value for farmers in Indonesia. One way of agricultural processing is to manufacture biocomposites such as rice straw fiber and glass fiber hybrid boards with PVAc polymer. This fiberboard material could potentially as structural materials and can an inexpensive because the fiber source is abundant and cheap. To increase the strength of the fiberboard made an initial process of soaking hay in an NaOH solution was conducted.
From this research it was found that the optimal composition of the rice straw board was at 30 % by weight of rice straw with a tensile strength of 4.5 Mpa, increased BLA % compared to tensile strength of the pristine PVAc. Moreover, the optimal composition of the hybrid board was 50 % rice straw, 50 % glass fiber and 70 % PVAC and this composition resulted a tensile strength of 4:26 MPa . The tensile strength of the hybrid board was smaller than that of the straw board becuase of the presence of big voids in between the straw and the glass fibers. Average moisture content of 10 % met the SNI 01-4449-2006 criteria , which was below 13 %.
"
Jakarta: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2014
T42673
UI - Tesis Membership  Universitas Indonesia Library
cover
Muthiah Hakim Hadini
"Penumpukan limbah konstruksi berkontribusi terhadap emisi karbon sehingga perlu dicari material alternatif yang ramah lingkungan. Biokomposit miselium merupakan material berkelanjutan dengan konsep material bio-based dan sirkular yang memanfaatkan limbah agrikultur. Penelitian ini bertujuan untuk meningkatkan kekuatan mekanis biokomposit miselium dengan konsep panel sandwich melalui penambahan lapisan. Eksperimen dilakukan memiliki dua tahap, yaitu (1) Komposit 1: Lapisan serat TKKS dengan resin getah pinus, dan (2) Komposit 2: Biokomposit Miselium. Pada komposit 1, hasil pengujian mekanis menunjukkan sampel S50 (Serat 50% dan resin 50%) dengan kuat tarik tertinggi (0.18 N/mm2) dan digunakan sebagai lapisan pada komposit 2. Pada komposit 2, dilakukan variasi perekatan lapisan dengan menggunakan hifa miselium (MB-M) dan resin (MB-R). Hasil pengujian karakter fisis, mekanis, dan konduktivitas termal dilakukan dan dibandingkan dengan standar JIS A 5905: 2003 kategori insulation board serta data sekunder dari penelitian terdahulu. Hasil tersebut menunjukkan sampel MB (tanpa lapisan) memiliki nilai mekanis dan konduktivitas termal terbaik. Hal ini dipengaruhi oleh metode inkubasi dan perekatan material yang menyebabkan perbedaan karakter akhir biokomposit miselium. namun nilai mekanis dan termal masih perlu ditingkatkan. Penelitian ini menyarankan perkembangan biokomposit miselium sebagai material nonstruktural yang mengarah pada fungsi panel insulasi.

Building and construction waste contributes to global carbon emissions, so it is necessary to seek alternative materials that are environmentally friendly. Mycelium biocomposite is a sustainable material with biobased and circular materials by utilizing agricultural waste. This study aims to increase the mechanical strength of mycelium biocomposites through sandwich panel concept by adding surface layer. The experiment was carried out in (1) Composite 1: Empty Fruit Bunch (EFB) fiber layer with pine resin, and (2) Composite 2: Mycelium Biocomposite. In composite 1, the mechanical test results shows S50 sample (50% fiber and 50% resin) has the highest tensile strength (0.18 N/mm2). In composite 2, layer bonding uses mycelium hyphae (MB-M) and resin (MB-R). The results of physical, mechanical and thermal conductivity testing results are compared with the JIS A 5905: 2003 standard and previous research. These results show that the MB sample (no added layer) has the best mechanical and thermal conductivity values. This is influenced by the incubation process by different material. However, the mechanical and thermal values still need to be improved. This research suggests the development of mycelium biocomposites as non-structural materials that lead to the function of insulation panels."
Depok: Fakultas Teknik Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Ismadi
"Pada penelitian ini telah dilakukan sintesis dan karakterisasi material komposit berbasis polyvinyl alcohol (PVA). Penelitian ini bertujuan untuk menganalisis pengaruh konsentrasi cross linker glutaral dehyde (GA) dan penambahan serat karbon terhadap sifat mekanik dan konduktivitas listrik komposit berbasis PVA dan potensinya untuk digunakan sebagai material shape memory polymer (SMPs). Konsentrasi GA yang digunakan adalah 0 dan 3% fraksi berat, sedangkan variasi konsentrasi serat karbon adalah 0, 2, 4, dan 6% fraksi berat. Sintesis film PVA dilakukan dengan cara melarutkan padatan PVA di dalam air pada suhu 80°C selama 6 jam dengan konsentrasi 8% dari berat air, dilanjutkan dengan pendinginan selama 12 jam. Selanjutnya ditambahkan GA dan serat karbon. Komposit diuji tarik dengan universal testing machine untuk mengetahui sifat mekaniknya, dilanjutkan dengan karakterisasi spektrum inframerah (FTIR), difraksi sinar X (XRD), analisis morfologi dengan SEM, karakterisasi termal (TGA), konduktivitas listrik dan uji shape recovery material. Dari hasil pengujian mekanik diketahui bahwa nilai kekuatan tarik menunjukkan peningkatan sebesar 16.9% dari 27.63 menjadi 32.3 N/mm2 dengan penambahan GA dari 0 ke 3%. Nilai kekuatan tarik optimal didapatkan pada penambahan serat karbon sebesar 2% yaitu 34.08 N/mm2 pada konsentrasi GA 0% dan 36.74 N/mm2 pada konsentrasi GA 3%. Dari spektrum inframerah terlihat adanya jembatan asetil sebagai akibat penambahan GA 3% yang menyebabkan peningkatan kekuatan ikatan kimia. Ukuran kristalit mengalami kenaikan dengan adanya penambahan GA 3% dan cenderung mengalami penurunan dengan adanya penambahan serat karbon yang terlihat pada hasil difraksi XRD. Analisis SEM menunjukkan tipe patahan getas pada penampang PVA dengan GA 3% dan fenomena fiber pull out pada penambahan serat karbon. Penambahan GA sebesar 3% menaikkan nilai konduktivitas listrik hingga 13.91%, dari 2.3 x 10-8 menjadi 2.62 x 10-8 S/cm, sementara penambahan serat karbon sebesar 2% menaikkan nilai konduktivitas listrik hingga 14000 dan 15900 kali pada kadar GA 0 dan 3%, yaitu sebesar 3.39 x 10-4 dan 4.18 x 10-4 S/cm. Secara umum, penambahan cross linker dan serat karbon mampu menaikkan nilai kekuatan tarik dan konduktivitas listrik secara signifikan pada material komposit berbasis PVA. Dari hasil uji shape recovery material terlihat bahwa nilai shape recovery komposit PVA dengan GA 3% bernilai di atas 80% menjadikannya berpotensi digunakan untuk aplikasi material SMPs.

Fabrication and characterization of polyvinyl alcohol (PVA) based composite has been done in this research to investigate the influence of concentration of cross linker glutaral dehyde (GA) and the addition of carbon fiber toward mechanical properties and electrical conductivity of PVA based composite, and also its potential as shape memory polymer (SMPs) material. The concentration of GA used was 0 and 3% of weight fraction, while variation of carbon fiber concentration was 0, 2, 4, and 6% of weight fraction. Fabrication of PVA film was done by dissolving PVA bulk into 80oC water for 6 hours with 8% concentration of w/w, continued with chilling for 12 hours and addition of GA and carbon fiber. Tensile test for the composite was done with universal testing machine to investigate the mechanical properties, continued with infrared spectrum (FTIR) characterization, X-ray diffraction (XRD), morphology analysis with SEM, thermal characterization (TGA), electrical conductivity and shape recovery measurement. From the mechanical testing, the tensile strength showed an increase of 16.9% from 27.63 to 32.3 N/mm2 with addition of GA from 0 to 3%. The optimal value of tensile strength was obtained with addition of carbon fiber of 2%, from 34.08 N/mm2 in GA concentration of 0% to 36.74 N/mm2 in GA concentration of 3%. The infrared spectrum showed an acetyl bridge as the result of addition of 3% GA which caused increasing in the strength of chemical bond. Crystallite size increased with addition of 3% GA and tended to decrease with the addition of carbon fiber which was showed in the XRD. SEM analysis showed brittle failure in the PVA morphology with 3% GA and a phenomenon of fiber pull out in the addition of carbon fiber. Addition of 3% GA increased the electrical conductivity of 13.91% from 2.3 x 10-8 to 2.62 x 10-8 S/cm, while addition of 2% carbon fiber increased electrical conductivity of 14000 and 15900 times at GA concentration of 0 and 3%, which were 3.39x10-4 and 4.18x10-4 S/cm. Generally, the addition of cross linker glutaral dehyde and carbon fiber reinforcement can enhance significantly the tensile strength and electrical conductivity of the PVA based composite. From shape recovery measurement, the shape recovery value of PVA composite with 3% GA is over 80%, thus it has the potential in application of SMPs material.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T35088
UI - Tesis Membership  Universitas Indonesia Library
cover
Rachmat Ferdian
"Kelangkaan minyak bumi yang tidak terbarukan terus mendorong kenaikan produk-produk turunannya, salah satunya adalah plastik. Untuk mencari alternatif dari hal tersebut, dikembangkanlah plastik komposit yang terbuat dari Polylactic Acid (PLA) dengan penambahan serat ijuk diharapkan mempunyai sifat mekanis yang cukup tinggi dan ramah lingkungan. Kompatibilitas dari kedua bahan tersebut menjadi perhatian utama untuk menciptakan material komposit dengan sifat mekanis yang baik. Penelitian ini menggunakan matriks PLA dengan serat ijuk yang dicampur dengan metode pelarutan menggunakan Dichloromethane dan kemudian dicetak menjadi sampel uji tarik dengan metode cetak panas. Variabel yang digunakan adalah fraksi volum penguat 0%; 10%; 20%; 30%; 40% dan 50%, serta modifikasi permukaan serat dengan perlakuan alkali (NaOH) 0,25 M selama 30 menit untuk meningkatkan kompatibilitas serat terhadap matriks. Hasil pengujian menunjukkan penurunan sifat kekuatan tarik dan Modulus Young terhadap fraksi volum penguat dari 0% hingga 50%, yang tidak menunjukkan efek penguatan serat terhadap matriks untuk sampel tanpa modifikasi perrmukaan, sementara nilai elongasi menunjukkan tren peningkatan. Hal ini diakibatkan kompatibilitas yang buruk antara matriks dan serat. Setelah dilakukan modifikasi permukaan serat, terjadi peningkatan dari sifat mekanis komposit tersebut. Hasil pengujian FTIR menunjukkan terjadinya pengurangan lignin dan hemiselulosa yang dapat meningkatkan kompatibilitas matriks dan serat.

Petroleum as a non-renewable resources shows price increment for its derivative products, which one of those is plastics. The development for an alternative solution are developed, that is composite material from Polylactic Acid (PLA) which combined with Ijuk (Arenga pinnata) with the main focus in their compatibility to meet the demand for high specific strength and environmetalfriendly material. This research use PLA as a matrices dan Ijuk as a reinforcement, which is solution mixed using Dicholoromethane and then pressed by hot pressing method to formed tensile test specimens. The variations are volume fraction and fiber surface modification. Volume fraction used are 0%; 10%; 20%; 30%; 40% and 50%, while alkali treatment with NaOH 0,25M for 30 minutes is used for surface modification. Tensile test results show the decreament in tensile strength and Young’s Modulus versus fiber addition from 0-50%, while the elongation shows the conversely results, is showing no strengthening effect of fiber to the matrices for untreated composites. This is due to poor compatibility between matrices and fibers. After surface modification, tensile test results show the improvement in the mechanical properties due to elimination of lignin and hemicellulose which increases its compatibility, supported by the FTIR test results.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T34974
UI - Tesis Membership  Universitas Indonesia Library
cover
Dirajaya PR
"Penelitian kekuatan komposit ferrocement dengan penambahan serat serabut kelapa untuk aplikasi lambung kapal adalah sebuah pembahasan ilmiah yang bertujuan untuk mendapatkan komposit yang baru dan dapat diaplikasikan sebagai material pembangun kapal.Serat alam yaitu serat serabut kelapa diaplikasikan sebagai serat (fiber) pada komposit FRC (Fiber Reinforced Concrete) jenis ferrocement. Serat alam sendiri memiliki kelebihan daripada serat sintetis dari segi karakteristik mekaniknya dan ketersediaannya yang berlimpah. Hal inilah yang menjadi latar belakang perlu dilakukannya penelitian mengenai serat alam.
Penelitian kali ini dilakukan untuk melihat karakteristik mekanis dari komposit tersebut. Sampel uji yang digunakan divariasikan sesuai dengan fraksi volumenya yang telah disesuaikan oleh persyaratan penggunaan serat pada FRC. Dilakukan pengujian di laboaratorium untuk melihat kekuatan tarik, besarnya defleksi,lebar retak,berat spesifik, water absorbtion dan kandungan air dari sampel uji. Dimana karateristik tersebut dibandingkan dengan data mekanis ferrocement yang telah diaplikasikan pada lambung kapal. Sedangkan sampel uji dengan penambahan serat serabut kelapa berkisar 5,7.5, 0 % dari volume fraksi sample.
Dari hasil pengujian test lentur dan didapat nilai kekuatan Beban lentur sebesar 403,33 ; 473,33 ; 501,67 dan 460 N pada masing-masing spesiemen (0,5,7.5 dan 10%), sedangkan dalam analisa struktur tegangan tarik pada masing-masing spesimen A =4,698 Mpa (681,377 psi),spesimen B = 5,833Mpa (826,247 psi),Spesimen C = 5,697 Mpa (845,995 psi) dan Spesimen D = 4,31 Mpa (625,213 psi). Hasil penelitian juga menunjukkan adanya hubungan antara defleksi, lebar retak, water absorbtion dan kandungan air dengan kenaikan fraksi volume serat serabut kelapa.

The research of ferrocement composite with adding coconut fiber for ship hull application is an scientific subject that purpose to get a new composite and applied for boat building. Natural fiber that's coconut fiber is used to as reinforcement in fiber reinforced concrete (FRC) inside of ferrocement. Coconut natural fiber has self uniques mechanical properties and widely available than syntetic fiber which is used for reinforcement. Based on it's research is carried out.
The research is done to observe mechanical properties of ferrocement composite. The variation of sample tests are prepared according to faction volume that's qualify of fiber reinforced concrete (FRC). Tests are done at laboratory to observe tensile strength, level of deflection, wide of crack, specific weight, water absorption, water content of sample tests. Those properties compare with mechanical properties of ferrocement that's applied for hull ship construction. The variation of sample tests which is adding of coconut fiber based on 5 %, 7,5 % and 10 % of faction volume.
The result of test shows flexural strength values are 403,33 ; 473,33 ; 501,67 dan 460 N for each specimen (0%,5%,7.5% and 10% faction volume). Result of analysis structure shows the tensile strength for each specimen that specimen A =4,698 Mpa (681,377 psi); specimen B = 5,833Mpa (826,247 psi); specimen C = 5,697 Mpa (845,995 psi) and specimen D = 4,31 Mpa (625,213 psi). The result shows relation of deflection, water absorption, water content with level of faction volume coconut fiber on specimen too.
"
Depok: Fakultas Teknik Universitas Indonesia, 2008
S38088
UI - Skripsi Open  Universitas Indonesia Library
cover
Rahmawati Kusumastuti Roosadiono
"Isolasi α-selulosa dari jerami padi telah berhasil dilakukan, menghasilkan rendemen sebesar 26,95%, indeks kristalinitas 74,28% dan berat molekul relatif 28.517 g/mol. Selulosa kemudian dimodifikasi, dengan tujuan untuk menghasilkan serat penukar ion, dengan mencangkokkan monomer asam akrilat pada selulosa menggunakan teknik kopolimerisasi cangkok pra-iradiasi. Kondisi optimum reaksi pencangkokan diperoleh pada dosis radiasi 30 kGy, konsentrasi monomer 10% volum, suhu 60oC dan waktu reaksi 120 menit, dengan persen pencangkokan rata-rata sebesar 84,12 % dan berat molekul sebesar 45.295 g/mol. Kapasitas pertukaran ion selulosa-g-AA yang dihasilkan dari pencangkokan sebesar 3,54 mek/g. Selanjutnya, untuk meningkatkan ketahanan kimia dan termal dari selulosa-g-AA, dilakukan pengikatan silang menggunakan agen pengikat silang N,N?-metilenbisakrilamida (MBA).
Kondisi optimum pengikatan silang terdapat pada dosis radiasi 15 kGy dan konsentrasi MBA 5%, dengan fraksi terikat silang yang diperoleh sebesar 68,27%, swelling dalam air sebesar 346,42% dan kapasitas pertukaran ion sebesar 2,99 mek/g. Pengikatan silang dapat meningkatkan ketahanan terhadap asam sebesar 3%, indeks kristalinitas sebesar 2,12%, suhu transisi gelas sebesar 20,43oC, dan suhu dekomposisi akhir sebesar 12,14oC. Selulosa terikat silang dapat digunakan sebagai penyerap ion logam Cu2+, dengan kapasitas adsorpsi sebesar 16,5 mg/g (konsentrasi awal Cu2+ 100 mg/L), yang diperoleh dengan dosis pengikatan silang 10 kGy dan konsentrasi MBA 3%.

Isolation of α-cellulose from rice straw has been successfully carried out having 26.95% yield, with 74.28% crystallinity index and relative viscosity average molecular weight 28,517 g/mol. The α-cellulose is then chemically modified to be a fiber ion exchanger, by grafting acrylic acid monomer onto cellulose using pre-irradiation graft copolymerization technique. The optimum condition for grafting is obtained at 30 kGy radiation dose, 10% monomer concentration, 60°C grafting temperature and 120 minutes reaction time, with 84.12% grafting average and relative viscosity average molecular weight 45,295 g/mol. The ion exchange capacity of cellulose-g-AA obtained from grafting is 3,54 meq/g. Furthermore, to improve thermal and chemical resistance of cellulose-g-AA, the sampel is crosslinked using N,N?-methylenebisacrylamide (MBA) crosslinking agent.
The optimum condition is obtained at 15 kGy radiation dose and 5% MBA concentration producing 68.27% crosslinked fraction, 346,42% swelling in water and 2,99 meq/g ion exchange capacity. The crosslinking process increases acids resistance by 3%, crystallinity index by 2.12%, glass transition temperature by 20.43°C, and final decomposition temperature by 12.14oC. Crosslinked cellulose-g-AA can be used as Cu2+ adsorbent having adsorption capacity of 16.5 mg/g (initial concentration of Cu2+ 100 mg/L). This capacity is achieved with crosslinking dose of 10 kGy and MBA concentration of 3%.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2013
T34799
UI - Tesis Membership  Universitas Indonesia Library
cover
Agus Subrianto
"Penggunaan serat alami seperti serabut kelapa pada bahan semen memodifikasi sifat reologi dari bahan pada kondisi segar dan sifat mekanik pada kondisi keras. Sifat fisik dan kimia dapat mengubah interface antara serat dan matriks selama pengerasan. Pada penelitian ini dilakukan pengujian terhadap matriks dan serat yang digunakan. Kemudian dilakukan proses fabrikasi sampel. Langkah terakhir dipelajari pengaruh beban yang diterapkan pada matriks terhadap ikatan antara matriks dan serat. Hasil pengujian menunjukkan bahwa penambahan serabut dalam air yang digunakan dalam pasta menurunkan kekuatan matriks. Sedangkan adhesi antara makriks dengan serat meningkat seiring dengan meningkatnya konsolidasi matriks.

The use of natural fibers such as coconut fiber in cementitious materials modifies the rheological properties of the fresh material and mechanical properties in the hardened state. Its physical and chemical properties can modify the interface between fiber and matrix during hardening. Initially the study and presentation of matrix and fiber used are provided. Then the process of samples fabrication is presented. In the last step, the influence of the load applied on the matrix to the adhesion between the matrix and fibers. Test results show that the addition of coir in the water used in the paste decreases the strength of matrix and the fiber-matrix adhesion increases with the growth of the matrix consolidation."
Depok: Fakultas Teknik Universitas Indonesia, 2013
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Agus Subrianto
"Penggunaan serat alami seperti serabut kelapa pada bahan semen memodifikasi sifat reologi dari bahan pada kondisi segar dan sifat mekanik pada kondisi keras. Sifat fisik dan kimia dapat mengubah interface antara serat dan matriks selama pengerasan. Pada penelitian ini dilakukan pengujian terhadap matriks dan serat yang digunakan. Kemudian dilakukan proses fabrikasi sampel. Langkah terakhir dipelajari pengaruh beban yang diterapkan pada matriks terhadap ikatan antara matriks dan serat. Hasil pengujian menunjukkan bahwa penambahan serabut dalam air yang digunakan dalam pasta menurunkan kekuatan matriks. Sedangkan adhesi antara makriks dengan serat meningkat seiring dengan meningkatnya konsolidasi matriks.

The use of natural fibers such as coconut fiber in cementitious materials modifies the rheological properties of the fresh material and mechanical properties in the hardened state. Its physical and chemical properties can modify the interface between fiber and matrix during hardening. Initially the study and presentation of matrix and fiber used are provided. Then the process of samples fabrication is presented. In the last step, the influence of the load applied on the matrix to the adhesion between the matrix and fibers. Test results show that the addition of coir in the water used in the paste decreases the strength of matrix and the fiber-matrix adhesion increases with the growth of the matrix consolidation."
Depok: Fakultas Teknik Universitas Indonesia, 2013
T35569
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>