Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 45562 dokumen yang sesuai dengan query
cover
"Since B A Tom 's found out the drag reduction phenomena, which occurs in polymer solutions in
1948 many studies, have been done for it because we can apply to the economizing energy system the
phenomena. The drag reduction is the application of the turbulent modification of the flow and we can
apply it for the turbulent flow region. We measured the turbulent pressure loss in the square ducts and
circular pipe flow of a guar gum solution by manometer, and found that the friction factor in the ducts
flow ware expressed by Re. Pressure loss in ducts ware measured for various concentrations of guar
gum and various diameters of pipes in water to study the effect of the additive on drag reduction, It is
found that guar gum acts like other drag reduction polymer additives because it constant the friction
factor in laminar regime, modify the transition to turbulent flow, and reduces the friction factor the fully
turbulent regime.
"
Jurnal Teknologi, 21(1) Maret 2007 : 32-38, 2007
JUTE-21-1-Mar2007-32
Artikel Jurnal  Universitas Indonesia Library
cover
"Luminar flow and turbulent of dilute polymer guar gum (fatter) solutions in smooth and in rough pines
was studied This experiment use in 25.4 mm of diameter pipe (PVC), which roughened by (k) 0, 34. 0,8
and 1, 59 mm roughness value of sand grain and 250, 500 and 1000 ppm for additive concentration. The
results show that flow properties ore influenced by polymer addition and surface roughness. In the
transition and turbulent flow regime without additive the increasing of friction coefficient appeared to be
effcted by wall condition alone. Addition of polymer to water is effective for rough pipe. For example
with addition of 1000 ppm of polymer reduced drag in k/D = 0,03 rough pipe by 24 percent at Reynolds
number 2 x 10 , whereas in 250 ppm addition tested drag was reduced only 5 percent
"
Jurnal Teknologi, 21 (2) Juni 2007 : 125-134, 2007
JUTE-21-2-Jun2007-123
Artikel Jurnal  Universitas Indonesia Library
cover
Reski Septiana
"Dalam hal transportasi fluida menggunakan pipa, penurunan koefisien gesek adalah aspek yang penting karena berkaitan dengan penghematan energi. Transportasi fluida tidak hanya menggunakan pipa bulat namun pipa lain seperti pipa persegi juga digunakan, khususnya untuk sistem ducting. Tujuan dari penelitian ini adalah untuk membandingkan perbedaan drag reduction yang dihasilkan oleh Agar dengan ketebalan coating 1mm dan 3mm. Pipa persegi dengan diameter hidrolis yang sama tanpa Agar coating digunakan sebagai pembanding. Fluida kerjanya adalah air. Konsentrasi Agar untuk coating-nya 5%. Penelitian dilakukan di aliran laminar dan transisi. Hasilnya menunjukkan semakin tebal coating Agar, maka semakin besar pengurangan hambatan gesek akan didapatkan.

Drag reduction in fluid transport is an important thing to discuss, related to energy saving. The most common pipe which is used in fluid transport is circular pipe. But in ducting system, rectangular pipes are also used. The goal of this research is to compare drag reductions of Agar coating 1mm and 3mm. Rectangular pipe with the same hydrolic diameter is used as a comparison. Working fluid is water. Agar concentration is 5%. This research focused in laminar and transition flow. The research?s results were obtained drag reduction about 15% of 3mm and 9% of 1mm Agar coating."
Depok: Fakultas Teknik Universitas Indonesia, 2016
S64814
UI - Skripsi Membership  Universitas Indonesia Library
cover
Adhitya Muakbar
"Pengurangan hambatan kapal sangat penting untuk mengurangi konsumsi bahan bakar. Hambatan-hambatan tersebut adalah hambatan gesek dan hambatan sisa, tetapi yang dominan dalam hambatan kapal merupakan hambatan gesek. Pengurangan hambatan kapal dapat dilakukan dengan menggunakan permukaan riblet. Struktur riblet yang paling umum ditemukan di alam adalah struktur riblet yang terputus-putus atau yang tersegmentasi (segmented riblet). Struktur riblet dengan perbedaan perbandingan tinggi dan jarak antar dinding (h/s ratio) menjadi fokus utama dalam penelitian ini. Dari hasil penelitian, struktur riblet mampu mengurangi hambatan total kapal hingga 14%.

Drag reduction is the most crucial step in order to reduce the use of gas for ships. The ship?s resistances consist of frictional resistance and residual resistance, but in the first one is more dominant in most drag cases. This has caused many researchers to find a way to reduce frictional resistance and one of many ways to do so is by applying a grooved structured surface, mostly known as riblets. Riblets can reduce the shear stress that any object makes when moving in fluid. There are many types of riblets in nature but mostly these types are segmented grooved structures rather than continuous ones. Given that riblet surfaces consist of aligned structures like walls, thus the main focus of this research is to analyze the difference in drag reduction by a riblet surface on ship hull when the ratio of riblet`s walls height and their distance with each other is varied. The result shows that a riblet surfaced ship?s hull can reduce drag up to 14 percent."
Depok: Fakultas Teknik Universitas Indonesia, 2014
T41550
UI - Tesis Membership  Universitas Indonesia Library
cover
Talahatu, Marcus Alberth
"Usaha para peneliti untuk menciptakan alat transportasi air (kapal) yang hemat energi terus dilakukan hingga saat ini. Modifikasi geometri, dimensi dan jumlah lambung merupakan suatu hal yang penting dalam usaha pengurangan hambatan kapal. Penggunaan Jenis kapal berlambung banyak katamaran dan trimaran mencapai angka 40% dari total kapal yang berlayar. Hambatan total kapal terdiri atas hambatan gesek dan hambatan sisa. Hambatan gesek merupakan fungsi dari geometris, perubahan tekanan, kekasaran permukaan dan coating pada permukaan lambung. Hambatan sisa fungsi dari gaya seret gelombang yang terbentuk oleh masing-masing lambung kapal. Dengan kemajuan ilmu material, diciptakan berbagai macam cat yang dapat berfungsi sebagai pelindung dinding kapal dan sebagai pengurang koefisien gesek. Kulit ikan belut yang mengandung lendir merupakan biopolimer yang ramah lingkungan dan tidak beracun.
Tujuan dari penelitian ini yaitu mengetahui efek variasi pelekatan biopolimer kulit belut (Monopterus Albus) pada lambung model kapal monohull, katamaran asimetris dan trimaran asimetris terhadap hambatan total model kapal dengan variasi bilangan Froude. Model kapal monohull, katamaran dan trimaran dengan pendekatan displacement yang sama dan diberikan variasi posisi pelekatan kulit belut pada lambung model kapal ditarik dengan variasi kecepatan pada kolam percobaan. Variasi sarat dan trim digunakan pada percobaan ini.
Pengukuran tegangan tali pada kecepatan kapal konstan (tercapainya terminal velocity) dilakukan dengan load cell transducer yang terhubung ke data akusisi. Percobaan dilakukan dengan teliti dan dilakukan pengulangan secepat mungkin untuk menghindari degradasi biopolimer lendir belut. Percobaan dilakukan pada air tawar dan perubahan temperatur seminimal mungkin (dijaga konstan). Hasil menunjukkan pelekatan biopolimer pada monohull menghasilkan drag reduction sebesar 8 % pada bilangan Re = 20.000. Pada kapal katamaran asimetris, S/L = 0,2 terjadi drag reduction sebesar 6 % pada bilangan Froude = 0,45. Pada kapal trimaran asimetris, S/L = 0,2 dan R/L = 0,0 terjadi drag reduction sebesar 10.4 % pada bilangan Froude = 0,35. Dimungkinkan efek biopolymer mempengaruhi distribusi kecepatan pada lapisan terluar (outer layer) sehingga laju kecepatan kapal bertambah.

Up to present time researchers are still continuously attempting to create energy saving water transportation vehicles (ships). Geometry, dimensions and number of hulls modification is an important effort to reduce the resistance of ship. The use of multi-hull ships such as catamaran and trimaran has reached 40% of total sailing ships. Total ship resistance consists of frictional resistance and residual resistance. Frictional resistance is the function of geometrics, pressure changes, surface roughness and coating of the hull surface. Residual resistance is the function of wave dragging force created by individual hull. With the advancement of material science various kind of paints have been created that could act as hull protection and as frictional coefficient reducer. Eel skin contents mucus that is environmentally friendly and non-toxic.
The objective of the research is to investigate the effects of Monopterus Albus biopolymer attachment variations on monohull, asymmetric catamaran, and asymmetric trimaran model hulls to ship model total resistance with variation of Froude numbers. Monohull, catamaran, and trimaran ship models with same displacement approach were attached with eel skin at various positions on their hulls, the ship models were towed with various speeds on the test basin. Variation of drafts and trims were applied on the experiment. The tensions of the towing string at constant ship speed (at the terminal velocity) were measured using load cell transducer which was connected to data acquisition. The experiment was conducted very carefully and repetitions were carried out very quickly in order to avoid the degradation of Monopterus Albus biopolymer. The experiment was carried out on fresh water with very little changes of temperatures (kept constant).
The results showed the attachment of biopolymer on monohull produced 8% of drag reduction at Re number = 20.000. On asymmetric catamaran with S/L = 0.2 produced 6% drag reduction at Fr = 0.45. On asymmetric trimaran with S/L = 0.2, and R/L = 0.0 produced 10.4% drag reduction at Fr = 0.35. These results are due to the effect of biopolymer in distributing the velocity at the outer layers that increase the velocity of the ships.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
D1453
UI - Disertasi Membership  Universitas Indonesia Library
cover
Sandi Siswantoro
"Salah satu fenomena menarik dalam fluida adalah terjadinya disipasi energi dalam aliran yang bergerak yang disebabkan adanya drag atau gaya hambat. Seringkali terjadi gradien kecepatan dalam hal aliran yang tidak dikendalikan oleh adanya batas padat (solid boundary). Hal ini kadang-kadang disebut ikhwal turbulensi bebas.
Viskositas adalah sifat tluida yang menyebabkan tegangan geser di dalam tluida yang bergerak; di mana viskositas adalah juga satu sarana dengan mana ketidak mampu balikan (irreversible) atau kemgian (losses) terjadi. Ungginya viskositas yang diperoleh terjadi karena adanya defonnasi molekul polimer dan bahwa fenomena ini merupakan mekanisme utama dan raduksi drag pada aliran turbulen.
Dalam fenomena transport, mereduksi drag bertujuan akhir untuk meningkatkan efisiensi dan meminimalkan kerugian yang timbul dalam aliran. Parameter penting yang mempengaruhi reduksi drag antara lain bilangan Reynolds, bobot molekul dan konsentrasi polimer, dan terjadi pada nilai terlentu dari tegangan geser dinding pelarutnya.
Pengaruh aditlf polimer terhadap reduksi drag terjadi hanya di atas bilangan kritis Reynolds terlentu yang tidak dipenganlhi oleh konsentrasi. Adlttf polimer mempengaruhi aliran di sekltar batas padat. Dengan tidak adanya batas, misalnya aliran jet bebas, aditif polimer ticlak mempunyai pengaruh terhadap karalctenstlk aliran.
Dalam daerah aliran yang mengandung aditlf, viskositas eddy yang ditemukan jauh lebih rendah daripada di air. Mekanisme ini dihubungkan kepada rusaknya eddy suatu ukuran yang berkorespondensi dengan ukuran lilitan molekul, sehingga mempengaruhi produksi dan transportasi disipasi energi turbulensi.
Hasil studi ini yang mengindikaslkan bahwa reduksi drag terjadi dalam batas keenceran yang tidak terbatas meyakinkan klta bahwa fenomena reduksi drag terjadi lebih dikarenakan adanya interaksi antara masing-masing molekul polimer yang terisolasi dengan Iingkungan pelarutnya daripada efek interpartikel."
Depok: Fakultas Teknik Universitas Indonesia, 1999
S36890
UI - Skripsi Membership  Universitas Indonesia Library
cover
M. Primadya Putra
"Kerugian jatuh tekanan (pressure drop) memiliki kaitan dengan koefisien gesek dan merupakan hal penting dari sistem aliran fluida di dalam pipa karena berhubungan dengan penggunaan energi. Air murni merupakan salah satu dari fluida-fluida sederhana yang digunakan pada penelitian kerugian jatuh tekan. Air merupakan fluida newtonian dimana viskositasnya hanya berpengaruh oleh perubahan temperatur. Penelitian ini dilakukan untuk mengetahui kerugian jatuh tekan yang terjadi pada aliran fluida dengan penambahan serat abaca. Dari pengujian ini didapatkan data debit aliran, perbedaan ketinggian air, dan kecepatan aliran. Spesifikasi dari alat pengujian yang diperlukan juga didapatkan untuk diolah menggunakan persamaan-persamaan empiris sehingga didapatkan hasil pengolahan. Tampilan grafik hasil pengolahan akan dibandingkan dengan grafik secara teoritis. Grafik yang ditampilkan merupakan hubungan antara bilangan Reynolds dengan beda tekanan dan bilangan Reynolds dengan koefisien gesek.

Pressure drop has a relevancy with the coefficient of friction and it?s significant case of the system of fluid rate in the pipeline cause it?s related with energy consumption. Pure water is one of plain fluids used on pressure drop research. Water is newtonian fluid which its viscosity depends on temperature change only. This research done in order to understand the pressure drop use abaca fibres. From the research obtains the capacity of rate, difference of water height, and velocity of rate. Specification of the equipment required is also getting to processing that uses empirical equations, so it will get the processing result. Processing result graphic will be compared with the theoritical graphic. The graphic being appeared is relation between Reynolds number with difference of pressure and Reynolds number with coefficient of the friction."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42155
UI - Skripsi Open  Universitas Indonesia Library
cover
Akbar Wicaksana
"Hambatan aerodinamis merupakan kontributor terbesar dalam konsumsi bahan bakar kendaraan darat, khususnya kendaraan komersial seperti bus dan truk yang memiliki geometri bluff body. Dimple yaitu cekungan pada bola golf telah lama diketahui dapat mengurangi drag, jika dibandingkan dengan bola golf tanpa dimple. Penelitian kali ini meneliti efek penambahan dimple pada permukaan atas model kendaraan yang disebut Ahmed Body. Variasi posisi dimple pada permukaan kendaraan model dilakukan untuk mengetahui penempatan dimple yang optimal. Pada percobaan kali ini, pengurangan hambatan terbesar yang dapat dicapai yaitu hingga 24%. Pada penempatan yang kurang tepat, dimple justru dapat meningkatakan hambatan hingga 13%. Uji sensitivitas performa dimple terhadap Reynolds number dan dimensi dimple, dilakukan dengan variasi kecepatan dan kedalaman dimple. Sensitivitas dimple digunakan untuk memperkirakan keefektifan dimple pada kendaraan skala sebenarnya.

Aerodynamic drag is a major contributor to the energy consumption of a land vehicle, especially commercial land vehicle such as trucks and busses. Dimples as on golf balls, is known to reduce the aerodynamic drag, ompared to golf balls without dimples. The objective of this paper is to investigate the effect of dimple to a land vehicle model, namely the Ahmed Body. Dimple's position is varied to investigate the optimal placement of dimple on the model. In the current experiment, the maximum aerodynamic drag reduction achieved is about 24%. While with an improper placement, the dimples increased drag up to 13%. To investigate the sensitivity of the dimple to Reynolds number and dimple's dimension, the velocity of the vehicle and dimple depth was varied. The dimple's sensitivity test is used to approximate the effectivity of the dimple on a real scale vehicle."
Depok: Fakultas Teknik Universitas Indonesia, 2010
S52192
UI - Skripsi Open  Universitas Indonesia Library
cover
Muhammad Raihan Setiawan
"Konsumsi daya yang tinggi pada sistem perpipaan diakibatkan oleh tingginya nilai jatuh tekan telah diakui sebagai hambatan yang terjadi pada aliran fluida di banyak industri, termasuk transportasi minyak bumi mentah di sektor migas. Untuk menyelesaikan masalah ini, Drag Reducing Agent (DRA) ditambahkan ke aliran minyak bumi mentah untuk meningkatkan efisiensi pompa. Salah satu DRA yang efektif secara teknis, murah, dan umum digunakan adalah surfaktan anionik. Kemudian daripada itu, karya tulis ini bertujuan untuk menginvestigasi pengurangan hambatan dengan penambahan surfaktan anionik berjenis sodium lauryl sulfate (SLS) di konsentrasi yang bervariasi pada aliran minyak bumi mentah dengan pipa spiral segilima. Efektivitas dari DRA diobservasi menggunakan pipa spiral segilima dengan rasio diameter (P/Di) sebesar 10,8 dan pipa bulat berdiameter 4 mm. Karya tulis ini menitikberatkan pada aplikasi pipa spiral segilima yang mengakomodir pengurangan hambatan yang maksimal pada aliran minyak bumi mentah. Kemudian, konsentrasi tertentu surfaktan anionic berjenis SLS diketahui secara aktif dapat menurunkan faktor gesek.

High power consumption in piping system due to high pressure losses in a turbulent flow has been recognized as a critical problem occurring to fluid flows in various industrial piping systems, including crude oil transportation in the oil and gas sector. To solve the problem, a drag reducing agent (DRA) is added into crude oil flow for improving the pumping efficiency. One of most technically effective, low costs and well-known DRA is anionic surfactant. Thus, this study aims at investigating the reduction of pressure drop by adding anionic surfactant sodium lauryl sulfate (SLS) at different concentrations into crude oil flow in a pentagon spiral pipe. Effectiveness of the DRA is comparatively observed in a pentagon spiral pipe with 10.8 ratio of diameter (P/Di) and in a circular pipe with 4mm inner diameter. This research particularly highlights the application of pentagon spiral pipe to provide the maximum drag reduction performance for crude oil flow. Then, a certain concentration of anionic surfactant SLS is observed to actively reduce friction factor."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Moh Taufik Muttaqin
"Pengurangan hambatan xanthan gum dalam larutan air telah dipelajari sebagai fungsi konsentrasi dengan menggunakan pipa acrylic yang telah dilakukan pengkasaran menggunakan pasir pada bagian dalam pipanya. Percobaan dilakukan dengan mengukur pressure drop. Tujuan penelitian untuk menyelidiki pengurangan gesekan dalam pipa acrylic dengan penambahan xanthan gum dalam larutan air. Pipa acrylic dengan diameter 12 mm digunakan dalam penelitian ini dengan variasi konsentrasi larutan xanthan gum 150 ppm, 300 ppm dan 400 ppm.
Percobaan dilakukan dari bilangan Reynolds rendah hingga tertinggi 38767,28. Penulis mengamati rasio penurunan hambatan maksimum yaitu sebesar 75,68% pada bilangan Reynolds 16415,99 pada pipa acrylic diameter dalam 12 mm dengan larutan xanthan gum konsentrasi 400 ppm. Penurunan koefisien gesek mengindikasikan keefektifan fluida uji sebagai drag reduction agent yang dapat dilihat dari koefisien gesek terhadap garis grafik Blasius.

The drag reduction of xanthan gum in aqueous solutions of was studied as a function of concentration with threacrylic pipes apparatus. Experiments were carried out by measuring the pressure drop. The purpose of this research is to investigate the reduction of pressure drop in a acrylic pipe with the addition fiber in aqueous solution. Circular pipe with diameter of 12 mm are used in this study.
Concentration of pandan fibers solutions are 150 ppm, 300 ppm and 400 ppm. Experimental was conducted from low to high Reynolds number up to 38767,28. We observed a maximum drag reduction ratio of 75,68 % at Reynolds number about 16415,99 with xanthan gum solutions concentration of 400 ppm. The pressure drop measurements indicate the effectiveness of xanthan gum as drag reduction agent which can be seen of drag coefficient curve compare to Blasius curve.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S47152
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>